Monte Carlo Trailing Arms Cutlass Rear 78-88 G Body lifted Bushings Installed

Price: 569.00 USD

Extended trailing arms for your 78-88 G Body lift kit project including bushings installed

Are you planning on putting a lift in the rear of your 78-88 G Body? Looking for the easiest solution with the fastest install? These Cutlass trailing arms with bushings installed fit all 78-88 Chevy G Body platform cars and are a necessity when lifting the rear of this car. These rear arms fit the following vehicles from 1978 to 1988: Buick Regal, 78-81 Buick Century, 78-88 Chevy El Camino, 78-83 Chevy Malibu, 78-88 Chevy Monte Carlo, 78-88 Oldsmobile Cutlass, 78-80 Pontiac Grand Am, 78-87 Pontiac Grand Prix, 78-81 Pontiac LeMans, 78-87 GMC Caballero and 82-86 Pontiac Bonneville. See fitment table below for a full list of applications.

The arms are a bolt-on design and are specifically designed for cars running lift springs or lift cups. The arms come with bushings installed. They are ready to install on your vehicle.

Why do I need longer trailing arms when lifting my G Body car?

When lifting the rear of 78-88 G Body vehicles, the trailing arms become too short to work efficiently. UCL extended rear trailing arms will solve many problems associated with running lift springs or lift cups such as the following:

• ● Adjustable rear arms will allow you to correct the pinon angle, also known as the drive shaft angle




• ● When lifting the rear, the drive shaft angle will not be in alignment without the arms




• ● You will experience drive shaft vibration without the rear trailing arms




• ● This can cause your U joints to fail prematurely, leading to an unsafe driving condition




• ● Your wheels will also move forward in the wheel well




• ● UCL extended adjustable arms will correct this issue as well




• ● The car can look funny with the wheel pushed forward in the wheel well

Universal Car Lifts extended Cutlass trailing arms fit all 78-88 G Body platform vehicles. They will greatly improve the performance of your lifted car application and are a necessity when raising the rear. They will also improve the appearance of the car and get rid of the issues associated with the wheel moving forward. For this reason, we highly recommend running these arms when lifting your Cutlass, Monte Carlo, Grand Prix, Malibu or any other Chevy G Body application.

How are UCL’s extended Cutlass trailing arms with bushings installed different from others?

Our longer trailing arms with bushings installed are the most durable on the market and are rated for over 1000hp. Constructed from high grade steel that is precision machined to exacting tolerances, UCL arms are over-sized and over-built for maximum performance. Some features include:

• ● Massive 1-3/4″ tubing construction is the largest in the industry to handle maximum abuse




• ● Arms are adjustable up to 3 inches over stock trailing arms




• ● Threaded adjustments allow you to fine tune your drive shaft angle to eliminate vibrations




• ● Upper and lower arms include high grade plated jam nuts for corrosion resistance




• ● UCL is the only company to utilize heavy duty boxed end construction for upper arms




• ● Bushings are included and installed by a factory technician




• ● Trailing arms are ready to install in the car with no prep work necessary




• ● Welded by certified welders using state of the art equipment

• ● Finished in a durable gloss black powder coat finish for years of trouble free use

We are so confident our Cutlass trailing arms with bushings installed are the best that we offer a lifetime warranty against manufacturers defects. Rest assured that by purchasing UCL extended Cutlass trailing arms, you are purchasing the best car lift products in the world.

Durable gloss black powder coating lasts 100x longer than spray painted parts

When choosing Cutlass trailing arms for your car lift project, be sure to note the finish on the parts. All of Universal Car Lifts parts feature a durable gloss black powder coat finish. We start by cleaning the raw metal parts with a degreaser solution to facilitate a permanent finish bonding. The parts are then sent through a large oven and heated to encourage off gassing. This uniformly bakes off any impurities from the parts.

After pretreating the parts in an oven, the Cutlass trailing arms are professionally sprayed with a high end powder coat gun in a clean room spray booth. The arms are then sent back through the oven where they bake at the proper temperature to obtain a permanent bond.

This powder coat technique is the same method that new car manufacturers use to ensure their parts last virtually forever. It prevents rust from forming on the parts which will weaken the steel and cause premature failure.

Beware of “knock-off brand” sellers who use cheap hardware store spray paint to finish their parts. The finish will look like crap and the parts will almost immediately rust. The corrosion will eventually cause the parts to fail and could cause your rear end to fall out of your car.

Insist on genuine UCL extended Cutlass trailing arms for your project. We have been manufacturing car lifts longer than anyone else and have more cars running our lifts than anyone else.

Your 78-88 G Body Cutlass trailing arms come with bushings installed

These trailing arms come with the bushings included and installed by a factory technician. Customers agree by far, this is the preferred method to go. Instead of dealing with using a hydraulic press, your trailing arms come ready to install. This saves time and frustration.

Do you really need new bushings? Chances are, your car’s factory bushings are over 20 years old. The rubber portion of the bushing deteriorates over time and when it does, your ride quality can suffer. Having new bushings installed will allow your car to ride better and have improved handling. The car will be tight like a brand new vehicle.

Using UCL trailing arms with bushings installed, you can be assured that your lift project will go as quickly as possible. Almost half of the time in an installation is spent getting the bushings pressed in. The car will be lifted faster and easier.

We beat all competitors prices on identical products

UCL is the largest manufacturer of car lift products in the world. We are confident our products are the best quality at the best prices. If you find a better price on an identical product, we will gladly beat it. Contact us directly via message or phone for more information. UCL has lifted more cars than anyone else and was the first company to offer car lift kits. Our customers have been riding high on our products for over 15 years.

Lifetime warranty, installation videos and extended technical support hours

UCL offers a lifetime warranty on every component we manufacture. We don’t expect you to use the warranty as we build our parts right the first time, so you won’t need to replace things later on. If the product fails just let us know and we will immediately send you a replacement free of charge.

Getting your longer Cutlass trailing arms installed quickly and trouble free on your 78-88 G Body is important. For this reason, we include an installation DVD that shows step-by-step how to install your products. We also include a printed installation manual.

We want your installation to be effortless. That is why we have experienced technicians on staff extended hours to make sure everything goes smoothly. Our technicians work set business hours and are easily reachable via email, messaging and phone. To contact us, simply click the “Contact Seller” option and then click “Other”. You should see our number listed. You can also look us up online.

Recent Feedback

coolbreeze444

Best product for the price

---

j1q

great price fast shipping thanks

---

usstev-cxisy3f

Fast shipping great seller

---

Fitment Guide

Make	Model	Years
Buick	Regal	1978-1988
Buick	Century	1978-1981
Chevy	Elcamino	1978-1988
Chevy	Malibu	1978-1983
Chevy	Monte Carlo	1978-1988
Oldsmobile	Cutlass	1978-1988
Pontiac	Bonneville	1982-1986
Pontiac	Grand Am	1978-1980
Pontiac	Grand Prix	1978-1987
Pontiac	Lemans	1978-1981
Gmc	Caballero	1978-1987